Build your own diy model car display case. Materials and tools.

If you’re particularly proud of your model collection and believe it deserves its own display case to show off to friends and family, you might want to try making a model car display case. This will help you to show off your favorite treasures to their full potential.

build your own diy model car display case
build your own diy model car display case

Materials and Tools

Materials and Tools
Materials and Tools

12 inch thick wood pieces
Measurement tape
Pencil
Sandpaper of fine grade
Panel tacks/pins
Tack hammer with 12-inch wood bit
Cabinet backking made of 1/8-inch thick hardboard
Power saw or handsaw
Glue for wood
Wood screws 112 inch
Face mask
Protective eyewear
Dowel is 12 inches thick.
Tack rag
Magnetic catches/hinges
Glass
Edging for picture frames
Framing staples ‘quarter’ beading for picture frames
Varnish or dye the wood
Brush for painting

Planning is the first step.

Planning is the first step.
Planning is the first step.

Measure the length and width of the automobiles you want to show. Because most model vehicles are 1:43 scale, your display box will be 3 inches thick if you allow 1 inch on either side of the car. Let’s pretend our cabinet is 24 inches tall and 12 inches broad.

Step 2: Putting the Cabinet Together

Step 2: Putting the Cabinet Together
Step 2: Putting the Cabinet Together

Cut two 12×3-inch pieces of wood and two 24×3-inch pieces of wood. This is the cabinet frame’s foundation. Use the butt joint, which consists of one component butting up against the other and being joined using glue and screws.

Make a box out of the wood pieces, using the longer pieces as sides. Make a note of where your screw holes will be. To avoid splitting, place the markings 12 inches from the edge of each side of the board and 12 inches from the short edge.

Drill all 8 holes that have been marked. Apply a little amount of wood glue to the edge that will be screwed together. To build the cabinet’s box frame, screw each panel together.

Mark the shelf locations on the interior of the cabinet. To manufacture dowel holes, use a 12-inch drill bit. Make 1 inch long pegs out of the wooden dowel. Apply a little quantity of glue to the dowel holes before inserting the 1-inch dowel pegs and gently hammering them into place with the hammer. Shelf length should be 1134 inches.

To attach the entire piece, pin the hardboard to the rear of the box frame. Hammer one panel pin into each corner of the backing board, then two on the longer side at equal distances, through to the frame. At equal distances, hammer one pin in the top and one in the bottom.

Making the Cabinet Door (Step 3)

Making the Cabinet Door (Step 3)
Making the Cabinet Door (Step 3)

The door is designed to seem like a picture frame. Cut the framing wood to the same size as the cabinet (12×24 inches), ensuring that each frame corner is precisely 45 degrees. Use wood glue to secure each corner, then staple the frame together with two staples in each corner.

Use the frame beading to attach the glass inside the frame. This features a circular border with a 90 degree corner carved out to rest on the frame’s two flat parts. Apply some adhesive to the edge that will be attached to the wood, and then tack it in place with care.

Step 4: Putting the Door Together

Step 4: Putting the Door Together
Step 4: Putting the Door Together

Make marks 2 inches from the top and bottom of the model car display case, depending on which side you want the door to hang. On the designated spots, screw the hinges to the cabinet box.

Carry on with the door, being careful not to shatter the glass. Place the shelves on top of the dowel pegs and stand the cabinet up. Using fine sandpaper, sand your cabinet. Remove any extra dust with a tack rag before varnishing. Use tiny magnets or hooks and eyes to fasten the door.

F.A.Q: Build your own diy model car display case.

Conclusions:

Cars are merely the beginning of the visual tale in places like this.
In the end, how a collector displays his or her model car collection is a matter of personal taste just as much as the cars themselves. We all have limitations, whether they are physical, financial, or otherwise, but with enough planning and ingenuity, we can all put up a model car display that expresses our enthusiasm in a unique way.

https://scaledworld.net/ will answer build your own diy model car display case.

  • 1/18 scale diecast car model display case cabinet
  • model car display shelves
  • how to build a model display case
  • 1/25 scale model car display case
  • diy model ship display case
  • toy car display shelf diy
  • how to make a hot wheels display case
  • 1/64 car display case diy

See more articles in category: Model car